Printable guitar template PDF?

[ChAoZ]

does anyone have a pdf for an ibanez destroyer template ,i read guitarnuts post on how to make one but it was further over my head than that dude that jumped from outer-space.

 

[pesimax]

Does anyone have a Template for a Airline Headstock? I've got the body and gonna buy a blank headstock neck....Go on throw me a bone.

Cheers

Like this

 

[Johnston]

does anyone have a pdf for an ibanez destroyer template ,i read guitarnuts post on how to make one but it was further over my head than that dude that jumped from outer-space.

This any use?

 

[ChAoZ]

This any use?

yes, if only i could figure out how to print it full size

 

[Johnston]

yes, if only i could figure out how to print it full size

I scaled it up using GIMP until the black line was measuring about 51mm.

Might be worth double checking another measurement though.

I tried posting the resulting JPEG but the forum must scale it down again.

 

[crazydave911]

yes, if only i could figure out how to print it full size

I scaled it up using GIMP until the black line was measuring about 51mm.

Might be worth double checking another measurement though.

I tried posting the resulting JPEG but the forum must scale it down again.

Once you get it scaled up.............select it with the "snapshot" tool and select print. In print options, select "landscape", "poster". It will tile the pic into pages that can be taped together

 

[ChAoZ]

ok gimp has downloaded gimp ,i have an image from sevenstring.org with a floyd rose which i know has a 74mm post spacing ,not sure how to enter this to re-scale the image

 

[storyboards27]

Fixed the peghead on the Coronet. ModerneGuy had pointed out to me that the tuner spacing was off for the 6 on a strip tuners that were used, so I realigned them for the hopefully correct 4 9/16" spacing.

https://www.dropbox.com/s/wfazv76oqutn9vv/'66 Epiphone Coronet.pdf

 

[Johnston]

ok gimp has downloaded gimp ,i have an image from sevenstring.org with a floyd rose which i know has a 74mm post spacing ,not sure how to enter this to re-scale the image

image removed

Use the icon fourth down on the left column to scale things bigger or smaller. Looks like a small square in the corner of a big one with an arrow. and the one above it that looks like a compass to click on a point and drag it to measure between two points.

At the bottom of the window where you can choose weather your image is 100% or not on screen you can select inches, MM or Pixels for your measurements. Beside that it'll show you the distance you measure with the compass.

Use the scale tool to make things bigger and then check it with the measuring tool until you have it right. Not forgetting to click on the wee chain bit in the scale dialogue box to keep the height and width ratio.

thats probably clear as mud

 

[ChAoZ]

image removed

Use the icon fourth down on the left column to scale things bigger or smaller. Looks like a small square in the corner of a big one with an arrow. and the one above it that looks like a compass to click on a point and drag it to measure between two points.

At the bottom of the window where you can choose weather your image is 100% or not on screen you can select inches, MM or Pixels for your measurements. Beside that it'll show you the distance you measure with the compass.

Use the scale tool to make things bigger and then check it with the measuring tool until you have it right. Not forgetting to click on the wee chain bit in the scale dialogue box to keep the height and width ratio.

thats probably clear as mud

yeah managed to do that eventually,but it only printed out the middle part of the picture and even that was still wrong when i measured between the posts

 

[rumblinbass]

Does anyone have the pdf's for an ASAT bass and a snakehead neck?

been through the thread but didn't see if there was a response to the request for the ASAT bass request.

 

[danecho283]

been through the thread but didn't see if there was a response to the request for the ASAT bass request.

i have requested the asat bass too! still waiting for someone to post it.

 

[Johnston]

yeah managed to do that eventually,but it only printed out the middle part of the picture and even that was still wrong when i measured between the posts

That I can't help with, I'm on Linux and it's probably different.

But I'm pretty sure somewhere on the forum someone has explained it in great detail. Maybe in the terry Downs template thread.

 

[studysession]

This thread is a gold mine for those who want to build their own. I just went through every page and cannot find what I am looking for.
Does anyone have any clean drawing for a Dean ML?

Thanks in advance!!

 

[Glen Smith]

Try this: http://www.gitarrebassbau.de/download/file.php?id=6202

 

[studysession]

Try this: http://www.gitarrebassbau.de/download/file.php?id=6202

Thanks!!!!

 

[soggybag]

Gibson 339

Anyone have plans for Gibson 339?

 

[justin72deluxe]

Anyone have a complete gibson blushawk? In pdf format?

 

[B0b E]

Anyone have plans for Gibson 339?

 

[Mark Simon Hell]

Anyone have plans for Ibanez Iceman Bolt-on or set-neck..?