parallel

  1. DerGrass10

    Help Needed: Position 2 (parallel) In 4-Way DIY Not Working?

    Hello, I am new to here. I recently (about 24 hours ago and then again the following morning) "installed" a 4 way switch in the ol' tele. I got the oak gribsy switch and followed the accompanying diagram from stewmac to the letter and everything works except the 2nd parallel position. Undeterred...
  2. B

    SSS wiring help

    Here are the sounds I want. 1. Bridge & Middle In Series 2. Bridge & Middle in Parallel 3. Bridge & Neck in Parallel 4 Neck & Middle in Parallel 5. Neck Controls - Master Volume, Tone on Bridge & Neck only I’m imagining there are two ways to do this and I’m wondering what the best/easiest...
  3. Sune Andersson

    How do I connect speakers with different configurations with an amp?

    I have a tube amp with two parallel output Jacks (marked Högtalare) and an impedance switch (4/8/16 or 100 ohms) marked Omkopplare. See images! I also have two 2x12” (8 ohms each speaker) cabs, that I want to be able to use either as one cab or two cabs together with this amp. Each cab can...
  4. tzumb

    Telestrat 4-way with phase, 2 volumes and master tone

    Hi everybody! I have been going at this for days, read fora, tried lots of stuff but I can't work it out. Will someone please help me with this? I'm wiring a strat pickguard with a tele-ish config (hence I'm on the tele forum. if you want me to move to the strat forum that's fine. Just let me...
  5. G

    Wiring Mod for H-S Tele

    Hi everyone, Decade long lurker, first time poster. About 7 years ago I built a Richie Kotzen inspired tele and found this forum super helpful just browsing the existing posts. I now have a wiring idea that I can't find the answer to anywhere, and I'm hoping someone here can help me out...
  6. pbenn

    Neck p/u straight-thru choice with 4-way switch?

    Can’t find layout for wiring 4-way switch this way, I’ve checked Fralin, SD, tdpri, Premier Guitar, etc: Mix (parallel with Neck straight thru and Bridge w/ tone) Neck straight thru Neck w/ tone Bridge w/ tone Is it impossible?
  7. V

    Nashville Deluxe series/parallel wiring with different brand pickups

    Howdy, I bought a nashville deluxe power tele, but I want to change the stock TexMex pickups and change the wiring to fit my needs. Because I often play higain and distortion, the pickups squeeled like a pig so they need to be changed with a set that is wax potted or noiseless. The nashville...
  8. newmindsets

    Tele Deluxe Wiring

    Hello all, I recently acquired a reissue 72 Tele Deluxe. I had the pickups rebuilt to vintage spec by Brandonwound pickups, so they have 4 wires. I have 2 CTS push pull pots which I've been trying to set up as Series/Parallel with Series(Fatter sound) being on when the pot is pushed in, and...
  9. itsGiusto

    Good mods to do with 4c humbuckers?

    For my Les Paul I'm planning on using two push-pull pots to coil-split, and one to phase-flip the bridge. So that leaves one additional push-pull DPDT switch. What are other good mods to try? Here are a few I'm considering: 1. Run neck pickup coils in parallel instead of series. Sounds like it...
  10. merseymale

    That tele 4-way mod on rotary switch?

    Does anyone know how to do the four way selector switch put on a rotary switch? I’ve seen a variation but it seems to be wired backwards in some way… 1)With the tone knob turns right towards the floor height once the bridge pick up on its own 2)The next position, turning the ‘tone knob’...
  11. Mexitele Blues

    Single ended parallel 6V6 power - matched pair or no?

    I have an old Gibsonette with the original Gibson branded RCA tubes. I'd like to hear what it sounds like with a fresh set. The power tubes share a bias resistor and cap. It seems to me that an unmatched pair might just sound a little fuller and richer. Whatch'y'all think? Am I barking up the...
  12. Binx

    Dpdt switch?

    Hi, I am working on putting together ideas for another build, and wanted to mess around a bit with some fun wiring options. Was thinking of doing an on/on/on switch for series/parallel/split. But I really don't want to use a mini dpdt switch, which is all i can find. Does anyone know if there is...
  13. W

    Squier Classic Vibe Duo Sonic 4-way HELP !!!

    As I want both parallel and series in my Duo Sonic, is there any way that I can mod it to have 1. Bridge only 2. Bridge and Neck Parallel 3. Neck only 4. Bridge and Neck Series? I have modded my tele into 4-way, but wondering if it can be possible for Duo Sonic also. I only see 3-way toggle...
  14. suburbansound16

    Tele 5 Way Wiring

    Hey there! I was wondering if anybody has a diagram on how to wire a 5 way blade style switch (regular or super) like this? 1) Bridge 2) Bridge + Neck, parallel 3) Neck 4) Bridge + Neck, series w/ bass cut 5) Bridge + Neck, series I've found similar but I'm really looking to do these exact...
  15. U

    Idea for series/parallel + coil tap wiring: feedback please?

    As someone relatively new to guitar pickups and their tonalities, I want a setup that lets me test humbuckers in series, parallel and split coil all in the same guitar. I couldn't find any exact wiring for what I had in mind, so I came up with this and thought I'd share (firstly to get feedback...
  16. J

    Wiring two humbuckers w/4-way switch & series/parallel push/pull pot

    Hello everybody! I decided to register since I've been just lurking around the forum for about three years now. So far I've been able to find answers to my questions without starting a new thread but this time I did not. Here's my problem: I have a Squier Classic Vibe Tele that I'd like to...
  17. Il Belva

    Three switches wiring

    Hello everybody, I'm new to this forum and this is my first post. I wanted to ask your opinion about a wiring that I'm designing for my DIY Tele. The idea is to use three DPDT on/off/ON switches instead of the 5-way switch that I'm using now and then the usual volume and tone pots. - Switch A...




Top