Recent content by Moldy Oldy

  1. Moldy Oldy

    What's on your workbench today?

    A friend brought over his AC15 because it was putting out much less volume than it should. Turned out to be a bad PI tube.
  2. Moldy Oldy

    Post a pic of the first guitar you ever made

    My avatar is my first one. In 2012 a couple friends and I decided we needed to try guitar building. Between us, my friend Scott was the only one with any woodworking experience or any decent tools. Virtually 100% of our guitar building knowledge came from here on TDPRI as I spent many hours...
  3. Moldy Oldy

    Choosing pickups for first electric guitar

    +1 Also, your taste/preferences will change over time as you begin to develop your own style. You’ll have a much better idea about what you want after you’ve been playing it for a year.
  4. Moldy Oldy

    SECOND CONSTRUCTION. 7 STRINGS, 27"

    If you think it’s that close maybe wait to level the fretboard. You can always level it after the guitar is assembled and you see how well it plays. For the nut, make one from scratch that fits your neck properly. They’re a bit tedious but not really that difficult if you go slow. You obviously...
  5. Moldy Oldy

    What's on your workbench today?

    The flame on that neck will be wonderful.
  6. Moldy Oldy

    One Curly Black Limba Snakehead, coming up!

    Bee-you-tee-full
  7. Moldy Oldy

    Aluminum pickguards

    Never made a pickguard with it, but you want 6061-T6 aluminum. It’s soft enough to machine easily but not gummy. Carbine router bits will work fine although you may not want to use them for wood again after that. Drill bits and countersinks will be fine. I have a bandsaw made for metal so I’ve...
  8. Moldy Oldy

    How can I...

    +1 for magnets. 3 or 4 half-inch diameter neodymiums on the body and the extension will hold it plenty strong enough. You could even bury them beneath thin wooden plugs or veneer strips so they would be nearly invisible. Do a good job gluing them with epoxy (rough them up really well first) or...
  9. Moldy Oldy

    okay folks..a Squier mustang project

    You didn’t mention how old your son is, but assuming he’s a teenager into Nirvana/Greenday he’ll never really be satisfied with single coils. It’s about 50% sound and 50% looks. For decent “budget” pickups, I haven’t used them personally but I’ve read lots of nice things about Bootstrap Pickups...
  10. Moldy Oldy

    First neck build - need some advice

    Congrats! It looks awesome.
  11. Moldy Oldy

    What's on your workbench today?

    Given the pain and suffering that will go into installing all the electronics, I’d recommend getting a genuine Switchcraft or Pure Tone jack instead of the one in your picture. Maybe also a Switchcraft switch instead of that one with the red lever.
  12. Moldy Oldy

    LP Junior Geometry - mortise/ tenon question

    I was thinking that too.
  13. Moldy Oldy

    Fret leveling with a beam: Am I the only one with this problem?

    They make aluminum necks. I Googled for 5 minutes and found 3 or 4 companies making them for around $700 - $1,000. I played a aluminum necked bass once. I remember the main sensation was that it was cold, which I did not like.
  14. Moldy Oldy

    LP Junior Geometry - mortise/ tenon question

    Yes, do the side drawing including accurate height of the bridge you will be using. My doublecut Jr. has the fretboard about 1/8” or a little less above the body at the joint. Otherwise the 2-3 degree neck angle will be to low. If I understand your question about the tenon sides, I think they...




Top