Asher Guitars WD Music Products Amplified Parts Mod Kits DIY Nordstarnd Pickups darrenriley.com
Asher Guitars WD Music Products Amplified Parts Mod Kits DIY Nordstarnd Pickups Warmoth.com
Asher Guitars WD Music Products Amplified Parts Mod Kits DIY Nordstarnd Pickups Warmoth.com

printer2's Recent Activity

  1. printer2 replied to the thread Can someone tier the fender Amps for me?.

    Blues Jr, EL84's. Somehow I don't think of Fender cleans when I think of this amp. Other than that people usually think Blackface...

    Aug 17, 2018 at 12:07 AM
  2. printer2 replied to the thread I roasted a maple billet in my home oven.

    Goes all the way through. It takes minimum an hour, I think I might have done the above between 1 1/2 to 2 hours. I have done stock...

    Aug 15, 2018 at 10:48 PM
  3. printer2 replied to the thread I roasted a maple billet in my home oven.

    For a few years I was looking after a number of heat treat ovens and furnaces, air, gas and vacuum for an aerospace manufacturer. I have...

    Aug 15, 2018 at 9:42 PM
  4. printer2 replied to the thread 20 lb Marshall (or Bassman) Inspired Amp.

    Sorry about that, missed the plate. I picked up a 26A7 which is designed to run off of 24V on the plate, it is a dual pentode output...

    Aug 15, 2018 at 11:37 AM
  5. printer2 replied to the thread 20 lb Marshall (or Bassman) Inspired Amp.

    I have over a dozen 12V6's I picked up for under $10 each, not going to find old stock 6V6's at that price. Speaking of, a 6V6 in a...

    Aug 15, 2018 at 9:51 AM
  6. printer2 replied to the thread 20 lb Marshall (or Bassman) Inspired Amp.

    I had the unfortunate luck of developing a neurological condition triggered by the fire retardant on my work clothing. When I am in pain...

    Aug 15, 2018 at 9:47 AM
  7. printer2 replied to the thread 20 lb Marshall (or Bassman) Inspired Amp.

    OK I give up. Well at least building amps this summer. Projects just keep popping up and less and less time to get anything done, done...

    Aug 14, 2018 at 10:47 PM
  8. printer2 replied to the thread What are the rules regarding signal loss in the pre amp - where does it occur, and where does it not.

    V = I*R Source has internal resistance and the individual components in the loop (from the power supply, through the tube, through the...

    Aug 14, 2018 at 3:28 PM
  9. printer2 replied to the thread Tick, Tick, Tick.....

    I had a ticking in an amp I built, thought how am I going to find this? As it happened it was not that hard to find it. Looking at the...

    Aug 14, 2018 at 9:18 AM
  10. printer2 replied to the thread New build, higher volume motorboating.

    Pull the tubes one at a time starting with the trem and verb. Move the verb power to the 18k, 5k node. If that does not help stick...

    Aug 13, 2018 at 12:05 PM
  11. printer2 replied to the thread Build DIY Hybrid Amp for cheap... Or am I cray-cray?.

    Try this. http://www.guitarscience.net/tsc/info.htm Impedance, there are ways of doing it but don't concern yourself too much with it...

    Aug 12, 2018 at 2:05 PM
  12. printer2 replied to the thread Build DIY Hybrid Amp for cheap... Or am I cray-cray?.

    Well so much for getting started on stuff, first off, http://ax84.com/p1/P1_Theory_Document.zip Explains a single ended amplifier,...

    Aug 12, 2018 at 10:01 AM
  13. printer2 replied to the thread World's Hottest Rain.

    Just looked at the forecast for tomorrow for my neck of the woods. I did a double take as today it was darn hot at 34 C, 93 F, tomorrow...

    Aug 11, 2018 at 11:15 PM
  14. printer2 replied to the thread Build DIY Hybrid Amp for cheap... Or am I cray-cray?.

    And here I am thinking your English is very good for someone from Greece. As far as a case is concerned it could be anything even wood....

    Aug 11, 2018 at 8:47 PM